Question: Why is my throttle sticking on my motorcycle?

A sticky throttle could be caused by worn cables, lack of lubrication in the cables or the cable getting bound up somewhere in the mechanism. Or it can be caused by an issue with the carburetor or EFI. … If the screws in the throttle housing are too tight it could cause the cable to stick.

How do you fix a throttle sticking motorcycle?

When the motorcycle throttle sticks to acceleration mode, pull on the clutch, shift to neutral, and turn off the motorcycle. Do not turn on the motorcycle until the issue is resolved. If the throttle sticks to the closed position, turn off the motorcycle and inspect and clean the throttle and the throttle cable.

How do you fix a sticky throttle?

How to Fix a Sticky Throttle on a Dirt Bike – Cheap, Easy, and Fast Solution

  1. 2.1 Remove Throttle Tube.
  2. 2.2 Wipe Down Handlebar and Throttle Tube.
  3. 2.3 Scotch-Brite Handlebar and Throttle Tube.
  4. 2.4 Apply Small Amount of Grease.
  5. 2.5 Tighten Bolts and Test.

What would cause throttle to stick?

A sticky throttle could be caused by worn cables, lack of lubrication in the cables or the cable getting bound up somewhere in the mechanism. Or it can be caused by an issue with the carburetor or EFI. … If the screws in the throttle housing are too tight it could cause the cable to stick.

IT IS INTERESTING:  How much does it cost to rent a motorcycle in Europe?

Can I use wd40 to lube throttle cable?

Choosing The Correct Lubricant

Some will think that any old lubricant will do, and that can’t be any farther from the truth. Some cables have a slick inner sheath that will gum up if exposed to solvents or harsh chemicals, so do NOT use WD-40 or any other type of penetrating oil.

Why is throttle free play important?

Yes, it is necessary. In simple words, throttle free play is a short bit of movement at the beginning of the throttle twist that has no effect. That free play allows you to bring the throttle open smoothly, and gently. … Throttle free play can make your bike more responsive and make it easier to ride smoothly.

How do I know if my throttle cable is bad?

Symptoms of a Bad or Failing Throttle Control Cable

  1. Improper cable adjustment and slow acceleration response. When there is excess slack or the cable is too tight, this can cause intermittent delays in throttle response relative to pressing down on the accelerator pedal. …
  2. Dirty or frayed cable. …
  3. Cruise control not working properly.

12 янв. 2016 г.

What is the best lubricant for motorcycle cables?

I would recommend that anyone using a motorcycle or bicycle with cable controls lubricate their cables with PJ1 Cable Lube. I’ve always sworn by PJ1 cable lube. It has great longevity, smells good, and the bubbling action really clears out dust/grit from cables as you pump it through with a cable-luber.

Why do some motorcycles have two throttle cables?

A push/pull throttle cable is an upgrade to the old standard single throttle cable linkage. … The second cable pulls the carb closed so it isn’t stuck wide open. On a road race bike at 165mph+ approaching a tight turn with little run off area, riders want that peace of mind that if they close the gas, it will close.

IT IS INTERESTING:  Is buying a motorcycle like buying a car?

What can I use to lubricate bike cables?

Lubricant. I use Tri-flow to lubricate cables, as it is very effective at distributing itself evenly, and lasts a long time. Most bike shops carry it, or they may have a similar product that will work just as well. Make sure you shake the bottle before use, and have a rag handy to wipe off any excess.

Do you need to lube new throttle cables?

Lube them all,any kind. I found it easier to lube from carb end up if already on bike. Taking apart the pull pull housing was more a pain.

How do you lubricate bike shifter cables?

Use a bike stand with a rotating head to get the cable end pointing up, then spray lube into hose. You can generally wait for gravity to the work the lube into the cable, but if the hose is long enough you can grab the end and squeeze the lube into the cable with your fingers.

Cycling