Are all bike chains the same width?

All modern bicycle chains are made to the “one-half inch pitch” standard, meaning from rivet to rivet is nominally 0.5 inches. The sprocket teeth are cut for this same one-half inch standard to accept bicycle chains. However, this does not mean all makes and models of chains are interchangeable.

How do I know my bike chain size?

Begin by counting the number of teeth on the largest front sprocket and largest rear. These numbers are often printed right on the sprockets and cogs. Next, measure the distance between the middle of the crank bolt to the rear axle. This is also the chain stay length.

Are 6 7 8 speed chains the same?

5, 6, 7 and 8 speed chains

Shimano, SRAM and Campagnolo all use the same chain with 8 speeds. Chain for 7 speeds is a bit wider – 7.3 mm, while a 6 speed one is substantially wider – 7.8 mm.

How do I know my chain size?

Go-kart chain numbers take the first letter from the pitch. And the last 1 or 2 digits from the roller width. For example a 420 chain has a pitch of 4/8-inches and a 520 chain has a pitch of 5/8-inches. To start measuring your chain size you need to start at the sprocket.

IT IS INTERESTING:  You asked: Which is the world's best cycle?

What is a narrow bike chain?

Narrow-wide chainrings have alternating narrow and wide teeth that fit into the inner and outer links respectively. This makes the chain more secure on the chainring and less likely to fall off. A narrow-wide ring is only necessary if you have a single chainring at the front and a rear derailleur.

How do I know if my bike chain is too short?

You should also see two slight bends at each jockey wheel of the rear derailleur. If the chain is too short, this shift is difficult to make and the derailleur cage is stretched out and almost parallel to the chainstay. If the chain is really short, then you might not even be able to shift into the largest cog.

Are bike chains universal?

All modern bicycle chains are made to the “one-half inch pitch” standard, meaning from rivet to rivet is nominally 0.5 inches. The sprocket teeth are cut for this same one-half inch standard to accept bicycle chains. However, this does not mean all makes and models of chains are interchangeable.

What size chain do I need for a 7 speed bike?

Bike Chain Size Chart

Drivetrain* External Width, in External Width, mm
9 speed 1/4″ – 9/32″ 6.5 – 7.0mm
10 speed 1/4″ – 9/32″ 6.0 – 7.0mm
10 speed narrow 7/32″ 5.88mm
11 speed 7/32″ 5.5 – 5.62mm

Can I replace a 7 speed cassette with an 8 speed?

A 7 and 8 speed cassette have the same amount of space between each cog. An 8 speed cassette is slightly wider than a 7 speed cassette because of that added gear. … Simply put – 8, 9, 10 speed cassettes all fit on the same hub. A seven speed cassette will fit on an 8 speed freehub with the use of a spacer.

IT IS INTERESTING:  How do you maintain a spin bike?

Is 8 speed bike enough?

8 speed rear cassette is good enough- Providing you get the range correct for your legs. But that is easier to do with 10 speed- I ride 8 speed(24) and 10speed (20) and have to admit that the 10 speed is easier to find the right cog. Even 7 speed is more than enough.

How do I know my roller chain size?

Most roller chain has the size stamped right into the side plates. You may see something like “40”, “C2080H” or “10B” stamped in, which the industry number that represents the chain size. Old chains will most likely need to be cleaned in order to see the size.

What size is 40 chain?

Chain standards

Size Pitch Maximum Roller Diameter
25 0.250 in (6.35 mm) 0.130 in (3.30 mm)
35 0.375 in (9.53 mm) 0.200 in (5.08 mm)
41 0.500 in (12.70 mm) 0.306 in (7.77 mm)
40 0.500 in (12.70 mm) 0.312 in (7.92 mm)

What size is 08B chain?

08B Roller Chain dimensions – ISO R606

Chain No. DIN P x W Width W (mm)
08B-1 1/2 X 5/16″ 7.75
08B-2 1/2 X 5/16″ 7.75
08B-3 1/2 X 5/16″ 7.75

What is a 3 32 chain?

3/32″ (0.094″, 2.30 mm) chain is used on derailer equipped bicycles that have more than 3 cogs at the rear. Even somewhat narrower chain, typically . 090″ or 2.29 mm between the inner plates, is used for derailer-equipped bicycles with 9 or more sprockets at the rear.

Do I need a chain guide with narrow-wide?

But what if you’re a competitive enduro racer? Then you need as much chain retention as you can get: narrow-wide, clutch, and chain guide. For years MRP scoffed at the folks that said you didn’t need to run a chain guide with a 1x narrow-wide setup, but they kept selling them anyways.

IT IS INTERESTING:  What is a good distance to bike for a beginner?

How do I know what speed my bike is?

Multiply the front gear number by the rear gear number to get the number of speeds. For example, if you have two front gears and five back gears, you have a 10-speed bike. If you have one front gear and three back gears, you have a 3-speed bike.

Cycling